Set to dry fire see below. The rear sight notch III can be adjusted in its width by screw 7.
Clockwise left. Close the breech flap. If no resistance is felt vwb reaching the indicated position, or resistance is felt before the edge, the absorber must be readjusted. Trigger Point Weight Turn screw 11 to increase trigger weight at point of release.
The price is obviously very good and really needs no discussion as common sense makes it blindingly obvious that this is the case - especially to a very experienced BBS "contributor" like yourself with over comments on 344 - but you do stand the chance of loosing this potential deal by bringing to to everyones attention. Cock the trigger. Takeup Travel Turn screw 10 anti clockwise to increase first stage travel.
Seal kit for feinwerkbau fwb p34 und p40
Turn screw 19 clockwise using a suitable screwdriver. To return to live fire mode you must again cock the pistol before pushing the catch-bolt to the right. Trigger Stop Screw 5. Turn screw 5 trigger stop approx one turn anti clockwise.
Ready sex contacts
Turn screw 4 slowly clockwise until the trigger releases. Cock and load the pistol. Check rearward piston movement repeat procedure 2 through 4 several times. Turn screw 19 anti clockwise using a suitable screwdriver.
Filling piece below rear sight may also be repositioned by loosening screw 17, shifting the piece, then retightening Fire pistol in a horizontal position. Absorber The P34 has a recoil absorber integrated in its receiver. When the trigger is released the valve at the intermediate chamber is opened by the firing piece and the propelling charge released.
It might be a better idea to wait until you are in the market to buy anything before starting yet another new thread about it. Due to the counter acting masses of pellet and piston the pellet impulse felt by the shooter is ificantly reduced. Check how far the breech could be opened until the position at which the resistance is felt.
Adjustment The absorber has been adjusted at the factory. Reference is the edge of the breech R. Cock the pistol.
Customers who bought this product also purchased
No resistance is felt after indicated rwb If the distance is too close to the rear sight holder, pull loading flap to its end position. Press the catch-bolt 6 to the left into the dry fire position. Trigger Adjustments Turn screw 3 clockwise to increase first stage weight.
Open slowly and carefully the flap until a slight resistance is fwv. Remove grip by unscrewing both 13 screws, lightly loosen screws 16, turn grip frame to desired position, then retighten screws Resistance is felt before indicated area If the distance is too far from the rear sight holder, pull loading flap to its end position. The propelling charge will drive the pellet out of the barrel, simultaneously the piston of the absorber is driven to the rear via a push cwb inside the bolt.
Operating the trigger in this mode will allow safe dry firing without releasing air. Cutaway Views. Sear Engagement It is recommended not to change factory adjustment. Aim at safe backstop.
34u stock chart
Grip Adjustments The P34 grip angles may be adjusted in the following ways: Inclination The grip rake may be adjusted up to 10 degrees by loosening screws 13, positioning the grip at the desired inclination, then retightening screws If this has already happened, the following will give a setting similar to original: 1. Mums the word!
A well used slogan and a piece of good advice made popular in WW2 but still very relevant today Last edited by zooma; at AM. Grip Turn The grip is adjustable 3 degrees either direction in relation to the barrel.
Readjust screw 5 trigger stop. Should the recoil rwb of the pistol change, ie if the shooter notices muzzle jump, the absorber should be readjusted: 1. Dry Firing Set the pistol on dry fire mode in the following manner: 1.
Maximum width 4. From this point back off screw 4 10 minutes to a quarter turn anti clockwise. The function of the absorber is okay if the strap underneath the flap - when opening it - being at the edge of the breech R or up to 3mm further.